Warning For your protection, please read the following: Water and Moisture: Appliances should not be used near water e. Warranty We at DigiTech are very proud of our products and back-up each one we sell with the following warranty: 1. Table of Contents Safety Information I Declaration of Conformity II Table of Contents Matrix - The matrix provides information regarding the current Preset, and Parameter edit functions.
Rear Panel 1. You can only view or download manuals with. Sign Up and get 5 for free. Upload your files to the site. You get 1 for each file you add. Get 1 for every time someone downloads your manual.
Buy as many as you need. View and download manuals available only for. Register and get 5 for free. Upload manuals that we do not have and get 1 for each file.
Get 1 for every download of your manual. Buy as much as you need. Safety Information Declaration of Conformity Table of Contents A Guided Tour Making Connections Mono Operation Stereo Operation Applying Power Battery Power About the RP Artist The Presets Performance Mode Rear Panel.
Getting Started. Making Connections. Stomp Loop. Effect Definitions. Unicord Uni-Vibe TM SynthTalk TM. Step Filter. Expression Update. Factory Reset. Expression Pedal Calibration. Preset Level USB Setup Noise Gates Chorus Stompbox Models. Tone Library Effects Library The warranty registration card must be mailed within ten days after purchase date to validate this warranty. DigiTech warrants this product, when used solely within the U. A Return Authorization number may be obtained from DigiTech by telephone.
Proof-of-purchase is considered to be the burden of the consumer. DigiTech reserves the right to make changes in design, or make additions to, or improvements upon this product without incurring any obligation to install the same on products previously manufactured.
The foregoing is in lieu of all other warranties, expressed or implied, and DigiTech neither assumes nor authorizes any person to assume any obligation or liability in connection with the sale of this product. In no event shall DigiTech or its dealers be liable for special or consequential damages or from any delay in the performance of this warranty due to causes beyond their control. NOTE :The information contained in this manual is subject to change at any time without notification. Some information contained in this manual may also be inaccurate due to undocumented changes in the product or operating system since this version of the manual was completed.
Congratulations on your purchase of the RP The RP Integrated Effects Switching System takes your tone to the next level giving you the control that you need over your external amp and stompboxes while packing in the power of a multi-effects processor.
Use the RP to control and spice up your tone without any compromises. Easily dial up a sound using the Tone and Effects Library knobs. You will appreciate the tone and dynamic interaction of each of the amps, stompboxes, and effects with your system.
Add USB support for computer recording and you have the RP the key to unlock your creative potential. We took a lot of care when we put this product together.
Everything should be included and in perfect working order. Help us get to know you by filling out the warranty card and sending it to us, or register online at www. Do yourself a favor and read the next couple pages before you start playing with your new RP There are two different ways to use the footswitches with the presets: Preset Mode and Pedalboard Mode.
Push the Pedalboard button just to the right of the knobs below the Display to toggle between these two modes. In Pedalboard mode, footswitches select presets, and footswitches act like pedals on a pedalboard.
That means you can turn the distortion, chorus, etc. To exit bypass mode and re-activate the preset you were in, just step the same footswitch again. To exit bypass mode and activate another preset, step on a different footswitch. You can also turn off the internal amps and cabinets for all the presets in the RP This is really useful when you just want to add effects processing to your own core amplifier sound. To begin tuning, play a note on your guitar a harmonic at the 12th fret usually works best.
The Numeric Display shows the note being played. Arrows on the right mean the note is sharp and should be tuned down. Arrows on the left mean the note is flat and should be tuned up. A left and a right arrow in the center mean the note is in tune.
The Expression Pedal controls the guitar volume while tuning. Next Page. Page 2 Harman International Industries Inc. Page 4 6. Page 5: Section One - Introduction That means you can turn the distortion, chorus, etc.
This is really useful when you just want to add effects processing to your own core amplifier sound. You can save changes to the User presets, but not the Factory presets. Displays The RP has two sets of displays. The 8 character alpha-numeric display shows preset names, bank names, and effects names while editing. The 2 character numeric display shows preset numbers and effects parameters while editing and shows the note being tuned when the Tuner is enabled.
Page 9 RP is connected to a computer and using recording software. The Looper can be used at any time during RP operation and offers the ability to create mono loop phrases of up to 20 seconds in length. First it is used to provide communication between the RP and the X-Edit editor librarian software.
Page Connection Setups Display will briefly read nO loop. The Stomp Loop will not enable when no connections are present at these jacks. Connection Setups The RP has many different connection options. Here are some more common ways it can be used: Left mono Line Output Preamp Input. Page 16 Amp Loop Return. Loop Return.
USB port on your computer. Page Applying Power That means you can turn the distortion, chorus, etc. The right 6 red LEDs indicate the note is sharp and should be tuned down. The center LED indicates the note is in tune. The output is muted in Tuner mode; rock the Expression Pedal to regain volume. Page Presets Value Buttons 1. Access the Tone Library 2. Access the Effects Library 3. Access the effects level with this button and select with this button and select with this button and adjust the a tone with the Value buttons.
The Footswitch on the right will select the next preset up, and the Footswitch on the left will select the next preset down.
Pressing both Footswitches together will bypass the currently selected preset. Display The Display provides information for different functions depending on the mode that has been selected. In Performance mode, the Display shows the currently selected preset num- ber. Before connecting the RP90, make sure that the power to your amplifier and the RP90 is turned off. There is no power switch on the RP Connect one cable to the input of one amplifier, channel of a mixer, or power amp.
Connect the second cable to a second amplifier, second channel of a mixer, or power amp. Page Applying Power Applying Power Before applying power to anything, set your amp s to a clean tone and set the tone controls to a flat EQ response on most amps, this would be 0 or 5 on the tone controls.
0コメント